Brandt KDF 1870 Edgebander (Used)
This machine is UL approved as a complete unit.
PC-20 Program Control
- PC: Industrial PC, 600 Mhz, Front side USB port.
- Memory: 256 Mb ram, 1 Gb Flash Card.
- Screen: 12.1” Color, 800 x 600 pixel, Active TFT Screen.
- Internal modem for remote diagnostic link.
Motorized top pressure beam for panel thickness adjustment. Smooth upper pressure rollers and
internal lighting.
Automatic feed track lubrication system. Program controlled in feed fence positioning
Automatic magazine for coil feeding from outside the machine.
Work piece gap optimization reduces spacing between parts to increase output.
Joint trimming unit for pre-trimming the work piece edge prior to processing.
Quick melt granulate glue application system with twelve minute heat-up time. Quick-change glue
tank for easy maintenance and glue color change, if necessary.
Infrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing
strength.
Program controlled positioning of the pressure zone. First pressure roller driven and three idle
pressure rollers.
Double motor end trimming unit with straight and chamfer capability. Chamfer up to 15. Program
controlled indexing from straight to bevel end trimming.
Top and bottom flush trimming unit. Includes straight insert cutters. Two position
vertical indexing for flush trimming or rough trimming. Servo motor program
control to edge thickness. This unit also tilts 0 – 25 degrees for bevel trimming HPL.
Fine trimming unit with DFC cutter head technology, servo motor control for side
copy positioning and to edge thickness for the unit. Auto tilt. Radius / straight DFC
cutters included. This unit provides superior dust flow control of the trimmed chips
and provides precise trimming due to location of the vertical copy rollers.
Multi Functional Contour trimming unit for continuous trimming and profile corner
trimming. Magnetic Linear drive system with soft touch feature.
Quick Change Scraping unit for rigid PVC edges. Program controlled indexing.
Finish scraping unit.
Oscillating Buffing unit with 2 motors, 0.18 kw each. 2 cloth buffing discs.
Isolation transformer with variable in feed voltage for balancing all three phases of
incoming power. This transformer will dampen line noise.
Technical Specifications
Edge band thickness 0.4 – 20 mm (0.016" - 3/4” )
Coil cutoff maximum 0.8 x 60 mm
3.0 x 45 mm (PVC)
3.0 x 33 mm ( Wood coils )
Edgeband height 12 - 65 mm (1/2" – 2 9/16 ")
Panel length min. 160 mm (6 3/8")
Panel width min. 70 mm (2 3/4")
Panel thickness - min.
- max.
8 mm (5/16")
60 mm (2 3/8")
Feed speed – variable 8 m/min (26 FPM) to 20 m/min
(65 FPM ); 16 m/min (52 FPM)
when edge thickness exceeds 3 mm.
14 m/min ( 46 FPM ) when corner
rounding.
Feed motor 2.2 kw (3 HP)
Joint trimming unit – two motors
Cutting speed
2.2 kw ( 3 HP each )
12,000 RPM
Pressure section First roller driven, 4 idle rollers
End trim unit - two motors
Cutting speed
Straight cut max.
.35 kw (1/2 HP ea)
12,000 RPM
20 x 45 mm (3/4" x 1 3/4")
Flush / Fine trimming unit
Cutter speed
Tilt range
1.85 kw ( 2.5 HP ) each
12,000 RPM
0 – 25 degrees
Fine trimming unit-auto tilt
Cutter speed
.55 kw (3/4 HP each)
12,000 RPM
Multi Function trimming unit - top
and bottom
0.4 kw (1/2 HP ea - two motors)
Total power required 35 kw
Amperage @ 230
@ 460
70 amps
35 amps
Machine length 6760 mm (22' 2”)
Machine width 1560 mm (61 ½ ")
Working height 950 mm (37 3/8")
Total height (hoods open) 2300 mm (7’ 6 ½”)
Machine net weight 3200 kg (7040 lbs.)
Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz.
Dust extraction:1x 120 mm (4 3/4"), 1x200 mm (8”), 1x 100 mm (4”), 3000 CFM.
Compressed air connection: 0.18 CFM per panel, 6 bars (85 PSI).
This machine is UL approved as a complete unit.
PC-20 Program Control
- PC: Industrial PC, 600 Mhz, Front side USB port.
- Memory: 256 Mb ram, 1 Gb Flash Card.
- Screen: 12.1” Color, 800 x 600 pixel, Active TFT Screen.
- Internal modem for remote diagnostic link.
Motorized top pressure beam for panel thickness adjustment. Smooth upper pressure rollers and
internal lighting.
Automatic feed track lubrication system. Program controlled in feed fence positioning
Automatic magazine for coil feeding from outside the machine.
Work piece gap optimization reduces spacing between parts to increase output.
Joint trimming unit for pre-trimming the work piece edge prior to processing.
Quick melt granulate glue application system with twelve minute heat-up time. Quick-change glue
tank for easy maintenance and glue color change, if necessary.
Infrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing
strength.
Program controlled positioning of the pressure zone. First pressure roller driven and three idle
pressure rollers.
Double motor end trimming unit with straight and chamfer capability. Chamfer up to 15. Program
controlled indexing from straight to bevel end trimming.
Top and bottom flush trimming unit. Includes straight insert cutters. Two position
vertical indexing for flush trimming or rough trimming. Servo motor program
control to edge thickness. This unit also tilts 0 – 25 degrees for bevel trimming HPL.
Fine trimming unit with DFC cutter head technology, servo motor control for side
copy positioning and to edge thickness for the unit. Auto tilt. Radius / straight DFC
cutters included. This unit provides superior dust flow control of the trimmed chips
and provides precise trimming due to location of the vertical copy rollers.
Multi Functional Contour trimming unit for continuous trimming and profile corner
trimming. Magnetic Linear drive system with soft touch feature.
Quick Change Scraping unit for rigid PVC edges. Program controlled indexing.
Finish scraping unit.
Oscillating Buffing unit with 2 motors, 0.18 kw each. 2 cloth buffing discs.
Isolation transformer with variable in feed voltage for balancing all three phases of
incoming power. This transformer will dampen line noise.
Technical Specifications
Edge band thickness 0.4 – 20 mm (0.016" - 3/4” )
Coil cutoff maximum 0.8 x 60 mm
3.0 x 45 mm (PVC)
3.0 x 33 mm ( Wood coils )
Edgeband height 12 - 65 mm (1/2" – 2 9/16 ")
Panel length min. 160 mm (6 3/8")
Panel width min. 70 mm (2 3/4")
Panel thickness - min.
- max.
8 mm (5/16")
60 mm (2 3/8")
Feed speed – variable 8 m/min (26 FPM) to 20 m/min
(65 FPM ); 16 m/min (52 FPM)
when edge thickness exceeds 3 mm.
14 m/min ( 46 FPM ) when corner
rounding.
Feed motor 2.2 kw (3 HP)
Joint trimming unit – two motors
Cutting speed
2.2 kw ( 3 HP each )
12,000 RPM
Pressure section First roller driven, 4 idle rollers
End trim unit - two motors
Cutting speed
Straight cut max.
.35 kw (1/2 HP ea)
12,000 RPM
20 x 45 mm (3/4" x 1 3/4")
Flush / Fine trimming unit
Cutter speed
Tilt range
1.85 kw ( 2.5 HP ) each
12,000 RPM
0 – 25 degrees
Fine trimming unit-auto tilt
Cutter speed
.55 kw (3/4 HP each)
12,000 RPM
Multi Function trimming unit - top
and bottom
0.4 kw (1/2 HP ea - two motors)
Total power required 35 kw
Amperage @ 230
@ 460
70 amps
35 amps
Machine length 6760 mm (22' 2”)
Machine width 1560 mm (61 ½ ")
Working height 950 mm (37 3/8")
Total height (hoods open) 2300 mm (7’ 6 ½”)
Machine net weight 3200 kg (7040 lbs.)
Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz.
Dust extraction:1x 120 mm (4 3/4"), 1x200 mm (8”), 1x 100 mm (4”), 3000 CFM.
Compressed air connection: 0.18 CFM per panel, 6 bars (85 PSI).
This machine is UL approved as a complete unit.
PC-20 Program Control
- PC: Industrial PC, 600 Mhz, Front side USB port.
- Memory: 256 Mb ram, 1 Gb Flash Card.
- Screen: 12.1” Color, 800 x 600 pixel, Active TFT Screen.
- Internal modem for remote diagnostic link.
Motorized top pressure beam for panel thickness adjustment. Smooth upper pressure rollers and
internal lighting.
Automatic feed track lubrication system. Program controlled in feed fence positioning
Automatic magazine for coil feeding from outside the machine.
Work piece gap optimization reduces spacing between parts to increase output.
Joint trimming unit for pre-trimming the work piece edge prior to processing.
Quick melt granulate glue application system with twelve minute heat-up time. Quick-change glue
tank for easy maintenance and glue color change, if necessary.
Infrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing
strength.
Program controlled positioning of the pressure zone. First pressure roller driven and three idle
pressure rollers.
Double motor end trimming unit with straight and chamfer capability. Chamfer up to 15. Program
controlled indexing from straight to bevel end trimming.
Top and bottom flush trimming unit. Includes straight insert cutters. Two position
vertical indexing for flush trimming or rough trimming. Servo motor program
control to edge thickness. This unit also tilts 0 – 25 degrees for bevel trimming HPL.
Fine trimming unit with DFC cutter head technology, servo motor control for side
copy positioning and to edge thickness for the unit. Auto tilt. Radius / straight DFC
cutters included. This unit provides superior dust flow control of the trimmed chips
and provides precise trimming due to location of the vertical copy rollers.
Multi Functional Contour trimming unit for continuous trimming and profile corner
trimming. Magnetic Linear drive system with soft touch feature.
Quick Change Scraping unit for rigid PVC edges. Program controlled indexing.
Finish scraping unit.
Oscillating Buffing unit with 2 motors, 0.18 kw each. 2 cloth buffing discs.
Isolation transformer with variable in feed voltage for balancing all three phases of
incoming power. This transformer will dampen line noise.
Technical Specifications
Edge band thickness 0.4 – 20 mm (0.016" - 3/4” )
Coil cutoff maximum 0.8 x 60 mm
3.0 x 45 mm (PVC)
3.0 x 33 mm ( Wood coils )
Edgeband height 12 - 65 mm (1/2" – 2 9/16 ")
Panel length min. 160 mm (6 3/8")
Panel width min. 70 mm (2 3/4")
Panel thickness - min.
- max.
8 mm (5/16")
60 mm (2 3/8")
Feed speed – variable 8 m/min (26 FPM) to 20 m/min
(65 FPM ); 16 m/min (52 FPM)
when edge thickness exceeds 3 mm.
14 m/min ( 46 FPM ) when corner
rounding.
Feed motor 2.2 kw (3 HP)
Joint trimming unit – two motors
Cutting speed
2.2 kw ( 3 HP each )
12,000 RPM
Pressure section First roller driven, 4 idle rollers
End trim unit - two motors
Cutting speed
Straight cut max.
.35 kw (1/2 HP ea)
12,000 RPM
20 x 45 mm (3/4" x 1 3/4")
Flush / Fine trimming unit
Cutter speed
Tilt range
1.85 kw ( 2.5 HP ) each
12,000 RPM
0 – 25 degrees
Fine trimming unit-auto tilt
Cutter speed
.55 kw (3/4 HP each)
12,000 RPM
Multi Function trimming unit - top
and bottom
0.4 kw (1/2 HP ea - two motors)
Total power required 35 kw
Amperage @ 230
@ 460
70 amps
35 amps
Machine length 6760 mm (22' 2”)
Machine width 1560 mm (61 ½ ")
Working height 950 mm (37 3/8")
Total height (hoods open) 2300 mm (7’ 6 ½”)
Machine net weight 3200 kg (7040 lbs.)
Electrical connection: 208/230 or 440/480 volt, 3-phase, 60 Hz.
Dust extraction:1x 120 mm (4 3/4"), 1x200 mm (8”), 1x 100 mm (4”), 3000 CFM.
Compressed air connection: 0.18 CFM per panel, 6 bars (85 PSI).
